The KM-30S is a door control card developed to eliminate installation difficulties due to lack of available space, minimize inefficient space-use and control heavy/light doors slowly or rapidly in a reliable manner without any vibration.

One of the biggest advantages is that it is just 30 millimeters high. This way, it can be mounted just behind the door jamb. This saves space on the cabin. In addition, the necessity to change the door parameters on the cabin is removed.

The KM-30S was designed to EN 81-20 standard. To comply with the EN 81-20 standard, when the KM-30S detects an obstacle, it stops closing and opens. When the door needs to be closed again, it closes slowly from the point where the obstacle was detected. This way, problems arising from jamming and collision are prevented. In addition, the software limits the pressure to 150Nm as required by the EN 81-20 standard. Since pressure above this level may cause injuries, this potential problem is prevented.

                The KM-30S also does not allow the control unit to move the cabin without making sure that the door is fully closed. For full compatibility with different control panels, it has dry contact relays which specify if “the door is fully opened,” “the door is fully closed,” or if “jamming has been detected.”

The KM-30S uses the “Smart Motor Control” method, which is one of today’s motor driving trends. “Standard Motor Control” is used in outdated technologies. The differences between these two methods are as follows: In Standard Motor Control, voltage and frequency are the basic control variables. Moment and flux are the components of these two variables.Because the speed control is performed by changing the V/Hz ratio in standard systems, the motor’s response to the applied PWM signals is connected to the weight (load) on the motor. The effect created by the moment and flux slows down the motor response. Due to this effect, control of motors using standard methods is limited. This limitation can be eliminated with vector controlled drives. Vector controlled drives use a much more effective motor driving technology. To ensure precise control, voltage and frequency interfere with the pulse-width modulation (PWM) signals in parallel with the target value. For a stronger, faster reaction, the voltage and frequency vectors must be calculated accurately. Microprocessors are used for this purpose. This allows the use of feedback information for ensuring the accuracy of the calculations. Vector control is performed with two systems: with sensor (closed loop) or without sensor (open loop). Sensor vector control, as the name implies, requires equipment forfeedback. In sensorless control, the AC driver follows the motor independently of the sensor and adjusts the voltage and frequency according to the current – torque character.

In contrast to the other door control cards, the KM-30S boasts two of the most distinctive features: door learning and motor recognition.

 

For motor recognition, information such as the user, motor current, pole number and gear ratio is confirmed in the menu. When the motor is run, the position and speed information of the door are also fed back via the encoder. With this feedback, discrepancies are detected and reported back to the motor. Therefore, the motor does not lose power. These features provide smooth transitions between the acceleration and deceleration curves in the ramp profiles. It also allows the door to open and close quickly, but smoothly. The door learning feature allows the user to connect the KM-30S to the door motor without any adjustment and activates the learning menu. The door limits are correctly set without limit switches and the door is now ready for use.

With the built-in temperature sensor, the motor energy is cut off in case of overheating to avert any potential danger.

In KM-30S, a Permanent Magnet Synchronous Motor (PMSM) was preferred. Nowadays, these motors have replaced the classic motors. They enable speed control at high intervals. Since they are brushless, they are smaller than DC motors. Another advantage of being brushless is that breakdowns are very rare and maintenance is easier. They can also be used with both low and high power. The Arkel KM-30S motor is designed specifically for the KM-30S and therefore works with high efficiency.

Mehmet Kurt Arkel R&D Hardware Design Specialist

Rate this item
(0 votes)
Haber Servisi

Asansör Vizyon Haber Servisi

Leave a comment

Make sure you enter all the required information, indicated by an asterisk (*). HTML code is not allowed.

Most Read

Panoramic View

Panoramic View

Apr 01, 2018 Rate: 0.00

Turkey Lift Sector Report 2017

Turkey Lift Sector Report 2017

Apr 01, 2018 Rate: 0.00

Last Tweets

16-18 Mart 2020'de Cezayir'deyiz https://t.co/MA2iaImwPi
ON MARCH 16-18, 2020 LIFT SECTOR WILL MEET IN ALGERIA https://t.co/omtDM9IQHf
Getirdiği mutluluğun tüm kötülükleri unutturacağı, başarıların tüm başarısızlıkları yok edeceği güzelliklerin hayat… https://t.co/2f27JxJZ3F
Takip Et Asansor Vizyon on Twitter

Content Gallery

ARTI KASNAK COMPANY STARTED PRODUCTION OF CAPTORMAL PULLEYS (MC NYLON 6)

ONAYLIFT ASANSÖR COMPANY MOVED TO THE NEW PRODUCTION PLANT WITH THE AREA OF 10,000 SQ.M

MR. UMUT ERDAĞ OF MIKROLIFT LIFTS: "MIKROLIFT PRODUCTS INSPECTS 2/5TH OF THE LIFTS MANUFACTURED IN TURKEY”

2ND INTERNATIONAL “ASCEN.TEC”:  ON MAY, 22 – 24, 2020 THE EXHİBİTİON FOR ELEVATOR TECHNOLOGİES

INTENSIVE PREPARATION FOR EXHIBITION OF THE LIFT AND ESCALATOR EQUIPMENT AVRASYA ASANSÖR (EURASIA LIFT)

AT SEELIFT 2019 SYMPOSIUM, SAFETY AND MODERNIZATION WERE ON THE AGENDA

ARKEL MANUFACTURES 150 THOUSANDS OF ELECTRONIC CARDS AND MANUFACTURES DEVICES AND 5 THOUSANDS OF CONTROL PANELS PER YEAR

NAGEL ASANSÖR WILL TRIPLE ITS CAPACITY IN THE YEAR 2020

BUTKON ASANSÖR PRODUCES CABIN AND FLOOR BUTTON PANELS USING THE NEWEST HIGH-TECH EQUIPMENT